Cable blowing machines · Made in Italy

Looking for "OFC cable blowing machine on rent"?

From last-mile connections to long-distance runs, a Fibernet technician can help you choose the right machine for your fibre optic cable installation.

Expert advice direct from the manufacturer / Free demonstration on request

Some of our customers.

Keep your installation moving with Fibernet cable blowing machines.

On-site training
Worldwide Technical support
Spare parts ready to ship
Replacement machine if yours breaks down

Photos and stories from installers, published by Fibernet.

Cable blowing machines in action.

Three installers testing the Opera cable blowing machine on siteEnlarge +
Opera with the installers on site.
A Fibernet technician showing installers how to use the cable blowing machineEnlarge +
Hands-on demonstration with a Fibernet technician.
Close-up of a Geniale cable blowing machine during an outdoor testEnlarge +
A closer look at Geniale in the field.
GoogleExcellentBased on 176 reviewsRead the reviews

Emanuele Zanda

Google review
Google

“An excellent experience on the installer training course. The whole team was professional and knowledgeable.”

Read on Google

Giuseppe Ares Rosa

Google review
Google

“I had the chance to try the Opera cable blowing machine on site…”

Read on Google

Paolo Manna

Google review
Google

“I really enjoyed this course. It took place in a pleasant setting with friendly, helpful people.”

Read on Google

Stories from installers

See the difference on site.

Testimonial · Opera

“We cut our working time by 80%.”

Experience on site

“2 km of cable in half a day.”

Hear the results from the installers themselves. Watch their testimonials right here.

Product videos

Meet the machines.

Product overview

LADY

Product overview

GENIALE

Product overview

OPERA

Three machines. Find your fit.

Every installation is different.
Find your cable blowing machine.

Start with the job at hand. Our technician can answer your questions about the right setup.

01 / SHORT RUNSFibernet Lady cable blowing machine

Compact and lightweight

LADY

A compact, lightweight machine for short runs.

Cable diameter
1.2–10 mm
Duct diameter
5–16 mm
Pushing force
Up to 150 N
Maximum speed
80 m/min
Cable protection
Twin drive beltsrubber-coated
I’m interested in Lady
02 / LONG RUNSFibernet Opera pneumatic cable blowing machine

Pneumatic power

OPERA

A pneumatic machine for long cable runs.

Cable diameter
4–16 mm
Duct diameter
7–63 mm
Pushing force
Up to 900 N
Maximum speed
110 m/min
Cable protection
Twin drive beltsrubber-coated
I’m interested in Opera
03 / ELECTRIC DRIVEFibernet Geniale electric cable blowing machine

Electric, with two gears

GENIALE

For short and long runs. Two gears let you match force and speed to the job.

Cable diameter
1.2–8 mm
Duct diameter
5–16 mm
Pushing force
400 / 110 NGear 1 / Gear 2
Maximum speed
60 / 125 m/minGear 1 / Gear 2
Cable protection
Twin drive beltsrubber-coated
I’m interested in Geniale

Specifications for the Fibernet range. The speeds shown are maximum values. Actual results depend on installation conditions and machine setup.

Direct from the manufacturer

The machine matters.
Who supports you
matters even more.

When you’re working on site, you need practical answers. With Fibernet, you speak directly to the people who design and build your cable blowing machine.

Speak to a technician

Direct support

A specialist technician can help when you need it.

Spare parts available

Spare parts ready to ship, direct from the manufacturer.

Replacement machine

If your machine breaks down, a replacement may be available within 48 hours.

Check availability and terms with your technician.

Dedicated training

Get help making the most of your machine, from your very first job.

See it in action before you choose

Put it to the test.
On your own site.

Request a free hands-on demonstration on your site or at Fibernet’s test facility. Discuss a real job with the technician.

Request a free demonstration
An operator using an Opera cable blowing machine on site

Start with the installation requirements, not just the hire period

Searching for an OFC cable blowing machine on rent usually begins with a practical deadline: a contractor has ducts ready, cable drums scheduled for delivery and a limited window in which to complete the blowing work. Before choosing equipment, however, the installation team needs to establish whether the proposed machine matches the cable, duct and site conditions. Cable outside diameter, duct internal diameter, cable construction, route length and the number of bends all influence the selection. None of these details should be considered in isolation. A combination that works well on a clean, straightforward route may require a different approach where ducts have tight bends, uncertain continuity or restricted access. Fibernet provides a manufacturer contact point for discussing these requirements, drawing on a technical background that began well before the company was established in 2001. Its founder, Giancarlo Trinei, worked on early optical cable installations in Italy during the 1980s, and the company introduced its first cable blowing machine, Lady, in 2021. For a contractor evaluating temporary equipment, this manufacturing perspective is useful because suitability must come before the commercial arrangement. A request for a fiber cable blowing machine on rent should therefore include more than the intended start and finish dates. Share the cable and duct dimensions, the expected blowing sections, the available compressor specifications and any access restrictions around the launch position. Where available, include cable manufacturer limits and route drawings so that the discussion is based on documented conditions rather than assumptions. Ask which guides, seals and other size-dependent components would be required, and whether these would be included in any proposed arrangement. Confirm the operating instructions, inspection requirements and responsibilities for wear or accidental damage before equipment reaches the site. Rental availability, geographical coverage, delivery arrangements and commercial conditions must be confirmed directly with Fibernet; the search term itself should not be taken as evidence that a rental service is offered for every destination or machine configuration. This is particularly important for international contractors coordinating work in Italy or arranging equipment for another country. Transport time, return logistics and local site readiness can affect the useful working period considerably. By submitting a clear technical brief through www.fibernetsrl.com, buyers can ask focused questions about machine compatibility and the options available for their project. The objective is not simply to secure equipment for a certain number of days, but to establish a workable installation plan with an appropriate machine, suitable accessories and clearly understood responsibilities. That preparation helps reduce avoidable delays caused by mismatched components, incomplete documentation or equipment arriving before the site is ready.

Check the complete blowing setup before work begins

A blowing operation depends on the interaction between mechanical cable feeding, compressed airflow and the condition of the installed duct. Selecting a cable blowing machine for fiber optic cable installation therefore requires a practical review of the whole setup, rather than a decision based on a headline distance or speed figure. Start with the duct. Confirm its identity, continuity and condition using the procedures specified for the project, and check that joints and connections are suitable for the intended operating conditions. Water, contamination, damaged sections or unexpected restrictions can undermine progress even when the machine itself is correctly selected. Next, review the compressed air supply. Compressor pressure and airflow are different specifications, and both need to be considered against the requirements of the proposed equipment and installation. Any air treatment, hoses and connections must also be appropriate for the system. Do not assume that a compressor already present on a construction site will automatically be suitable. When discussing an OFC cable blowing machine on rent, ask for the documentation needed to verify these points before committing to a work schedule. Cable handling deserves equal attention. The drum should be positioned to allow controlled payout, with the cable protected from sharp edges, excessive bending and unnecessary resistance before it enters the machine. Operators need to understand how the selected equipment controls feeding and what limits apply to the cable. Machine settings should follow the relevant instructions and cable specifications, not improvised values intended to overcome an unexplained obstruction. If progress changes unexpectedly, the appropriate response is to stop safely and investigate the cause rather than continue increasing force or pressure. The working area should also allow access to controls, safe management of hoses and clear communication between personnel at the launch and receiving locations. For a contractor seeking a fiber optic cable blowing machine on rent, these operational details belong in the initial enquiry because they can reveal missing accessories or unsuitable site arrangements before delivery. Ask whether the proposed configuration includes the correct cable guides, duct connections and sealing components, and clarify which consumables need to be sourced separately. Discuss how equipment condition will be checked at handover and what information should accompany any request for technical assistance. Fibernet's development of the Lady machine provides a relevant starting point for a product discussion, but compatibility, supplied components and operating limits should always be confirmed for the actual configuration under consideration. No universal installation distance can responsibly be promised without assessing the route and operating conditions. A carefully specified setup gives the site team a stronger basis for planning realistic production, recognising abnormal behaviour and protecting both the cable and the equipment throughout the blowing operation.

Compare temporary access with ownership using the full project cost

The decision between temporary access and purchasing a machine becomes clearer when the contractor examines its actual workload. An isolated installation package may justify a different approach from a continuous programme involving several crews and repeated mobilisation. The number of planned blowing days matters, but so do the gaps between them, the predictability of the schedule and the cost of having equipment unavailable when ducts are finally released for installation. A search for an OFC cable blowing machine on rent is therefore best treated as the beginning of a commercial and technical comparison, not as a complete procurement specification. If a rental option is available, request written clarification of the charging period, delivery and collection responsibilities, deposit arrangements, condition reporting and treatment of delays. Establish whether accessories are included and how additional days would be handled if access permits, weather or preceding civil works disrupt the programme. These questions are especially relevant where equipment must cross borders, because transport and administrative requirements may represent a significant part of the overall commitment. Equally, a fiber cable blowing machine price should be evaluated against the supplied configuration rather than treated as a directly comparable figure on its own. Ask what the quotation includes, which cable and duct dimensions the proposed setup supports, what documentation accompanies it and which additional components might be needed for future projects. Ownership can provide scheduling flexibility for a busy contractor, but it also brings responsibilities for storage, inspections, maintenance and keeping suitable accessories available. Temporary access may reduce the need to hold equipment between projects, yet its value depends on confirmed availability and practical logistics. Neither option is automatically preferable without understanding the contractor's operating pattern. Fibernet's family-led business combines its origins in Italian technical experience with an ambition to serve the international market. The generational transition that began in 2010 brought Matteo, Marta and Ismael into the company, while the launch of Lady in 2021 marked a specific milestone in its machine development. For English-speaking contractors working in Italy or planning installations elsewhere, this background offers context for speaking directly with the manufacturer about equipment requirements. It does not replace the need for a written quotation or confirmation of destination-specific supply arrangements. Prepare a concise project summary covering installation location, timing, cable and duct sizes, expected workload and compressor availability. Include whether the enquiry concerns a single project or a longer series of contracts. Contact Fibernet through www.fibernetsrl.com to establish which supply options can actually be offered and what further information is required. A well-prepared enquiry supports a more meaningful comparison of cost, suitability and scheduling risk, helping procurement teams make a decision that reflects conditions on site rather than the attraction of an initial headline figure.

Still looking for information about OFC cable blowing machine on rent?

Fill in the form and discover what Fibernet Srl can do for you!

Contact us!

Before you get started

Have a question?
Start here.

If you prefer, speak to us directly.

+39 346 652 9915
Which cable blowing machine is right for my site?

Compare the cable diameter, duct diameter and installation distance. Lady is compact and lightweight for short runs. Opera is pneumatic and designed for long runs. Geniale is electric and handles both. A Fibernet technician can help you choose.

Can I see the machine in action before I buy it?

Yes. You can request a free hands-on demonstration on your site or at Fibernet’s test facility. Tell us what you need in the form and a technician will arrange it with you. Request a demonstration.

How much does a Fibernet cable blowing machine cost?

To get a price, contact a Fibernet adviser using the form or call +39 346 652 9915.

What support will I get after purchase?

Fibernet offers direct technical support, spare parts ready to ship and dedicated training. If your machine breaks down, a replacement may be available. Ask your technician about availability and terms.

Your next project
starts with the right choice.

Tell us about your job. We’ll help you find the right cable blowing machine.

CallRequest information