Cable blowing machines · Made in Italy

Looking for "drill powered fibre optic cable blower"?

From last-mile connections to long-distance runs, a Fibernet technician can help you choose the right machine for your fibre optic cable installation.

Expert advice direct from the manufacturer / Free demonstration on request

Some of our customers.

Keep your installation moving with Fibernet cable blowing machines.

On-site training
Worldwide Technical support
Spare parts ready to ship
Replacement machine if yours breaks down

Photos and stories from installers, published by Fibernet.

Cable blowing machines in action.

Three installers testing the Opera cable blowing machine on siteEnlarge +
Opera with the installers on site.
A Fibernet technician showing installers how to use the cable blowing machineEnlarge +
Hands-on demonstration with a Fibernet technician.
Close-up of a Geniale cable blowing machine during an outdoor testEnlarge +
A closer look at Geniale in the field.
GoogleExcellentBased on 176 reviewsRead the reviews

Emanuele Zanda

Google review
Google

“An excellent experience on the installer training course. The whole team was professional and knowledgeable.”

Read on Google

Giuseppe Ares Rosa

Google review
Google

“I had the chance to try the Opera cable blowing machine on site…”

Read on Google

Paolo Manna

Google review
Google

“I really enjoyed this course. It took place in a pleasant setting with friendly, helpful people.”

Read on Google

Stories from installers

See the difference on site.

Testimonial · Opera

“We cut our working time by 80%.”

Experience on site

“2 km of cable in half a day.”

Hear the results from the installers themselves. Watch their testimonials right here.

Product videos

Meet the machines.

Product overview

LADY

Product overview

GENIALE

Product overview

OPERA

Three machines. Find your fit.

Every installation is different.
Find your cable blowing machine.

Start with the job at hand. Our technician can answer your questions about the right setup.

01 / SHORT RUNSFibernet Lady cable blowing machine

Compact and lightweight

LADY

A compact, lightweight machine for short runs.

Cable diameter
1.2–10 mm
Duct diameter
5–16 mm
Pushing force
Up to 150 N
Maximum speed
80 m/min
Cable protection
Twin drive beltsrubber-coated
I’m interested in Lady
02 / LONG RUNSFibernet Opera pneumatic cable blowing machine

Pneumatic power

OPERA

A pneumatic machine for long cable runs.

Cable diameter
4–16 mm
Duct diameter
7–63 mm
Pushing force
Up to 900 N
Maximum speed
110 m/min
Cable protection
Twin drive beltsrubber-coated
I’m interested in Opera
03 / ELECTRIC DRIVEFibernet Geniale electric cable blowing machine

Electric, with two gears

GENIALE

For short and long runs. Two gears let you match force and speed to the job.

Cable diameter
1.2–8 mm
Duct diameter
5–16 mm
Pushing force
400 / 110 NGear 1 / Gear 2
Maximum speed
60 / 125 m/minGear 1 / Gear 2
Cable protection
Twin drive beltsrubber-coated
I’m interested in Geniale

Specifications for the Fibernet range. The speeds shown are maximum values. Actual results depend on installation conditions and machine setup.

Direct from the manufacturer

The machine matters.
Who supports you
matters even more.

When you’re working on site, you need practical answers. With Fibernet, you speak directly to the people who design and build your cable blowing machine.

Speak to a technician

Direct support

A specialist technician can help when you need it.

Spare parts available

Spare parts ready to ship, direct from the manufacturer.

Replacement machine

If your machine breaks down, a replacement may be available within 48 hours.

Check availability and terms with your technician.

Dedicated training

Get help making the most of your machine, from your very first job.

See it in action before you choose

Put it to the test.
On your own site.

Request a free hands-on demonstration on your site or at Fibernet’s test facility. Discuss a real job with the technician.

Request a free demonstration
An operator using an Opera cable blowing machine on site

Choose cable blowing equipment around your actual installation

Selecting a drill powered fibre optic cable blower starts with understanding the cable, the duct and the conditions your installation team will encounter. A machine that suits one combination of cable diameter and duct size may not suit another, even when the planned installation distance appears similar. For telecommunications contractors working across Italy, access chambers, changes in direction, duct joints and variations in route preparation all influence the practical demands placed on cable blowing equipment. Before requesting a recommendation, gather the cable manufacturer's installation limits, the duct's internal and external diameters, the expected route length and details of the available compressed air supply. These facts provide a more useful starting point than a headline speed or distance quoted without operating conditions. A drill driven fibre optic cable blower uses a drill to provide mechanical drive, while compressed air supports the cable's movement through a suitable duct. The exact drive arrangement, drill compatibility and operating procedure must be checked against the selected machine's documentation. Do not assume that any cordless drill, coupling or speed setting will be appropriate. Equally, a drill does not replace the need to assess air pressure, airflow and the condition of the duct. Cable stiffness, sheath material and friction can affect feeding behaviour, making correct adjustment important from the beginning of the installation. Ask how the proposed equipment accommodates the cable, how the drive pressure is adjusted and what provisions help the operator respond to an obstruction. Excessive pushing force can damage a cable, so operating limits should always follow the relevant equipment and cable instructions. Fibernet brings an Italian technical background to these discussions. Founded in 2001, the company developed its cable blowing activities through practical engineering experience and introduced its first cable blowing machine, Lady, in 2021. For a contractor comparing a cable blower for fibre optic cable, that background offers a basis for a focused conversation about the application rather than a decision based on appearance alone. Contact Fibernet with a clear description of your intended work and ask which configuration, accessories and operating requirements should be considered. Include photographs or specifications of the cable and duct where available, together with information about site access and the compressor you intend to use. This allows the discussion to address the complete installation arrangement, including connections, handling and preparation. It also helps distinguish essential compatibility requirements from optional conveniences. The objective is not simply to obtain a machine, but to identify a workable cable blowing setup that your team can prepare, operate and maintain according to documented instructions.

Prepare the drive, air supply and duct before cable feeding

Reliable cable blowing depends on preparation as much as on the equipment selected. Before positioning a drill powered fibre optic cable blower, establish a stable working area and organise the cable drum so that the cable can feed without unnecessary resistance or tight bends. Check that the route is ready for installation and that the receiving end is controlled by an informed colleague. Any duct inspection, cleaning or integrity testing should follow the duct supplier's guidance and the procedures approved for the project. Dirt, water, poorly assembled joints or unexpected restrictions can undermine an otherwise suitable setup. A compressed air fibre optic cable blower also requires attention to the air supply as a complete system. Compressor capacity, hose diameter, connection restrictions and leaks can influence the air available at the machine. Pressure alone does not describe the compressor's suitability; airflow under the intended operating conditions matters as well. Confirm the required air characteristics with the equipment supplier, and never exceed the permitted ratings of the machine, duct, hoses or fittings. Where the equipment instructions require air treatment or lubrication, use the specified arrangement rather than improvising with unsuitable materials. The drill deserves the same disciplined approach. Confirm its approved operating mode, coupling, direction of rotation and speed range before starting. A battery powered fibre cable blower arrangement may make the mechanical drive easier to position where mains electricity is inconvenient, but a battery driven drill does not automatically make the entire blowing setup independent of other equipment. The air supply must still be planned, and spare batteries should be considered where compatible with the approved drill configuration. During setup, ensure that guards, cable guides and seals are fitted correctly. Adjust the drive mechanism according to the instructions, avoiding unnecessary clamping force on the cable sheath. Begin with a controlled operating procedure and monitor how the cable responds rather than increasing drive effort to overcome unexplained resistance. A sudden change in feeding behaviour is a reason to assess the installation, not to assume that greater force will solve the problem. Stop and isolate the equipment before making adjustments whenever the operating instructions require it, and depressurise the system before opening pressurised connections. Record useful installation information such as the cable and duct combination, route conditions, equipment settings and any interruptions. These records can help your team prepare subsequent sections more consistently without treating earlier results as a guarantee. When discussing equipment with Fibernet, explain how your crews organise these activities on site. Practical details about transport, chamber access, compressor positioning and daily handling can be just as important as the nominal cable dimensions when assessing a suitable cable blowing configuration.

Evaluate the complete equipment package and long-term requirements

A useful quotation for a drill powered fibre optic cable blower should make clear what is included and what your team must provide separately. Ask for an itemised description of the machine configuration, cable and duct adaptation components, drill connection requirements, air fittings and any accessories proposed for your application. Check whether a drill, compressor, hoses, transport case or spare wearing parts are included rather than assuming that photographs show the exact supply package. Comparing quotations on this basis helps procurement teams understand whether apparently similar offers actually cover the same installation needs. When assessing fibre optic cable blower price, consider the complete cost of putting the equipment into service. A lower initial figure may not include the components needed for your cable range, while a more comprehensive package may reduce additional purchasing and compatibility checks. Neither price nor the number of accessories proves that a machine is suitable. The decisive question remains whether the documented configuration matches the work your crews need to perform. Ask about replacement seals, drive components and other service items relevant to the proposed model, including how they are identified and ordered. Clear maintenance instructions and a defined route for technical enquiries can make equipment management easier over its working life. A used fibre optic cable blower introduces further questions. Its condition, maintenance history and completeness should be examined alongside the asking price. Wear in the cable contact surfaces, missing adaptation parts or uncertainty about approved operating limits can affect the practicality of a purchase. Request the applicable documentation and inspect the equipment before making assumptions about its readiness for site work. For new equipment enquiries, Fibernet's history provides context for the people behind the discussion. The business was founded by Giancarlo Trinei following extensive technical experience in Italy, and a generational transition began in 2010 with Matteo, Marta and Ismael joining the company. This family continuity sits alongside the company's ambition to develop its position internationally in cable blowing machines. Buyers in Italy and English-speaking purchasing teams abroad can use the website to begin a direct conversation about their requirements. For deliveries outside Italy, request confirmation of destination availability, shipping arrangements, lead times and the documentation applicable to the proposed order. Do not assume that every configuration has identical delivery conditions or regulatory requirements. Provide the delivery location, expected purchasing schedule and intended cable blowing applications when requesting a quotation. Ask for written confirmation of specifications, warranty terms and support arrangements before ordering. This creates a clearer basis for comparing equipment and helps align purchasing decisions with the realities of installation work, rather than relying on broad performance claims that may not reflect your route conditions.

Still looking for information about drill powered fibre optic cable blower?

Fill in the form and discover what Fibernet Srl can do for you!

Contact us!

Before you get started

Have a question?
Start here.

If you prefer, speak to us directly.

+39 346 652 9915
Which cable blowing machine is right for my site?

Compare the cable diameter, duct diameter and installation distance. Lady is compact and lightweight for short runs. Opera is pneumatic and designed for long runs. Geniale is electric and handles both. A Fibernet technician can help you choose.

Can I see the machine in action before I buy it?

Yes. You can request a free hands-on demonstration on your site or at Fibernet’s test facility. Tell us what you need in the form and a technician will arrange it with you. Request a demonstration.

How much does a Fibernet cable blowing machine cost?

To get a price, contact a Fibernet adviser using the form or call +39 346 652 9915.

What support will I get after purchase?

Fibernet offers direct technical support, spare parts ready to ship and dedicated training. If your machine breaks down, a replacement may be available. Ask your technician about availability and terms.

Your next project
starts with the right choice.

Tell us about your job. We’ll help you find the right cable blowing machine.

CallRequest information