Cable blowing machines · Made in Italy

Looking for "drill powered cable blowing machine"?

From last-mile connections to long-distance runs, a Fibernet technician can help you choose the right machine for your fibre optic cable installation.

Expert advice direct from the manufacturer / Free demonstration on request

Some of our customers.

Keep your installation moving with Fibernet cable blowing machines.

On-site training
Worldwide Technical support
Spare parts ready to ship
Replacement machine if yours breaks down

Photos and stories from installers, published by Fibernet.

Cable blowing machines in action.

Three installers testing the Opera cable blowing machine on siteEnlarge +
Opera with the installers on site.
A Fibernet technician showing installers how to use the cable blowing machineEnlarge +
Hands-on demonstration with a Fibernet technician.
Close-up of a Geniale cable blowing machine during an outdoor testEnlarge +
A closer look at Geniale in the field.
GoogleExcellentBased on 176 reviewsRead the reviews

Emanuele Zanda

Google review
Google

“An excellent experience on the installer training course. The whole team was professional and knowledgeable.”

Read on Google

Giuseppe Ares Rosa

Google review
Google

“I had the chance to try the Opera cable blowing machine on site…”

Read on Google

Paolo Manna

Google review
Google

“I really enjoyed this course. It took place in a pleasant setting with friendly, helpful people.”

Read on Google

Stories from installers

See the difference on site.

Testimonial · Opera

“We cut our working time by 80%.”

Experience on site

“2 km of cable in half a day.”

Hear the results from the installers themselves. Watch their testimonials right here.

Product videos

Meet the machines.

Product overview

LADY

Product overview

GENIALE

Product overview

OPERA

Three machines. Find your fit.

Every installation is different.
Find your cable blowing machine.

Start with the job at hand. Our technician can answer your questions about the right setup.

01 / SHORT RUNSFibernet Lady cable blowing machine

Compact and lightweight

LADY

A compact, lightweight machine for short runs.

Cable diameter
1.2–10 mm
Duct diameter
5–16 mm
Pushing force
Up to 150 N
Maximum speed
80 m/min
Cable protection
Twin drive beltsrubber-coated
I’m interested in Lady
02 / LONG RUNSFibernet Opera pneumatic cable blowing machine

Pneumatic power

OPERA

A pneumatic machine for long cable runs.

Cable diameter
4–16 mm
Duct diameter
7–63 mm
Pushing force
Up to 900 N
Maximum speed
110 m/min
Cable protection
Twin drive beltsrubber-coated
I’m interested in Opera
03 / ELECTRIC DRIVEFibernet Geniale electric cable blowing machine

Electric, with two gears

GENIALE

For short and long runs. Two gears let you match force and speed to the job.

Cable diameter
1.2–8 mm
Duct diameter
5–16 mm
Pushing force
400 / 110 NGear 1 / Gear 2
Maximum speed
60 / 125 m/minGear 1 / Gear 2
Cable protection
Twin drive beltsrubber-coated
I’m interested in Geniale

Specifications for the Fibernet range. The speeds shown are maximum values. Actual results depend on installation conditions and machine setup.

Direct from the manufacturer

The machine matters.
Who supports you
matters even more.

When you’re working on site, you need practical answers. With Fibernet, you speak directly to the people who design and build your cable blowing machine.

Speak to a technician

Direct support

A specialist technician can help when you need it.

Spare parts available

Spare parts ready to ship, direct from the manufacturer.

Replacement machine

If your machine breaks down, a replacement may be available within 48 hours.

Check availability and terms with your technician.

Dedicated training

Get help making the most of your machine, from your very first job.

See it in action before you choose

Put it to the test.
On your own site.

Request a free hands-on demonstration on your site or at Fibernet’s test facility. Discuss a real job with the technician.

Request a free demonstration
An operator using an Opera cable blowing machine on site

Choose cable blowing equipment around the job, not assumptions

Selecting a drill powered cable blowing machine starts with understanding the installation conditions your team will actually encounter. Cable diameter, duct internal diameter, route length, bends and access arrangements all influence whether a proposed configuration is suitable. For telecommunications contractors working on Italian sites or planning projects abroad, the most useful starting point is a clear technical description of the job. Fibernet welcomes enquiries from companies seeking cable blowing equipment and a practical discussion of their requirements. Rather than choosing equipment from a headline distance alone, provide the cable and duct specifications, describe the route, and explain how your crew intends to organise the installation. This gives the equipment supplier a meaningful basis for assessing compatibility and identifying details that require confirmation before purchase. A drill powered fibre cable blowing machine uses a drill to drive its mechanical feeding arrangement, while compressed air assists cable movement through the duct. The precise operating method, approved drill characteristics and air requirements depend on the individual machine, so these must be checked against its documentation. Drill power should not be confused with the air supply: a suitable compressor and correctly prepared connections may still be necessary. Likewise, the presence of a cordless drill does not establish that every part of the installation system is battery operated. Understanding these distinctions helps purchasing teams compare proposals accurately and avoid overlooking essential supporting equipment. Before requesting a quotation, record the cable manufacturer's installation limits, including permissible pushing force and minimum bend radius where specified. Check that the proposed duct is suitable for cable blowing and that its joints, seals and route have been assessed appropriately. An apparently straightforward run can become difficult if duct damage, contamination or tight changes of direction create resistance. Equipment selection should therefore consider both the machine and the condition of the installation path. When evaluating a drill driven cable blowing machine, also ask about the cable gripping arrangement, available guides, sealing components and adjustment procedures. These details affect preparation, changeovers and the operator's ability to maintain controlled feeding without damaging the sheath. Ask which components are included in the proposed supply and which must be selected separately for your cable dimensions. Fibernet's technical background provides context for this application-led conversation: founded in 2001, the company developed its first cable blowing machine, Lady, in 2021. For your next installation, contact Fibernet with concrete project information and request confirmation of the proposed equipment's capabilities, limitations and supply configuration. A well-defined enquiry makes it easier to assess suitability before your crew arrives on site.

Prepare the duct, air supply and feeding arrangement as one system

On site, successful cable blowing depends on more than the drive mechanism. The cable, duct, air supply and feeding equipment must work together within their respective operating limits. Before setting up a drill powered cable blowing machine, the installation team should review the manufacturer's instructions and establish a safe working arrangement around the launch point. Position the cable drum so that the cable can unwind smoothly, without sharp changes of direction or unnecessary drag. Secure the machine using the mounting method specified for that model, and leave sufficient access for adjustments and inspection. A clear working area helps operators observe the cable entry and respond promptly if feeding becomes irregular. Duct preparation deserves equal attention. Check the intended route, assess continuity and use appropriate procedures to establish that the duct is clean and suitable for blowing. Connections should be correctly assembled and rated for the planned operating conditions. Any lubricant must be compatible with the cable, duct and equipment, and used according to the relevant instructions. Never assume that additional pressure will resolve an obstruction or that a higher feeding speed will produce a better installation. If progress changes unexpectedly, stop and investigate using the prescribed procedure rather than increasing force without understanding the cause. When assessing a drill powered fibre optic cable blowing machine, ask how operators should set the feeding arrangement and which checks are required before air is introduced. The relationship between mechanical assistance and airflow matters because excessive pushing can buckle or damage a cable, particularly where resistance develops near the entry point. Adjustments must remain within the equipment and cable manufacturers' limits. Record the starting conditions and monitor the installation so that changes in behaviour can be recognised early. Where the selected equipment provides measurement or protective features, confirm how they operate rather than assuming that every model includes them. Comparing a battery powered cable blowing machine with a drill-driven arrangement also requires care. The phrase can describe different power configurations, and it does not, by itself, specify compressor requirements, available pushing force or cable compatibility. Request a clear explanation of what is powered electrically, which external supplies are needed and how the proposed configuration suits your site. For contractors moving between multiple work areas, these practical distinctions influence transport planning, charging arrangements and equipment readiness. Fibernet can be approached with these operational questions when discussing a proposed supply. Share the space available at the launch point, the expected working conditions and the dimensions of the cable and duct. This allows the enquiry to focus on a usable installation setup rather than an isolated machine description, helping your purchasing and site teams evaluate the same requirements before making a decision.

Build a clear purchasing brief for Italian and international projects

For a contractor buying cable blowing equipment, a useful quotation should explain what is being supplied and how that configuration relates to the intended work. Start your enquiry for a drill powered cable blowing machine with a concise project brief: identify the cable construction and outside diameter, the duct dimensions, the anticipated route conditions and the equipment already available to your crew. Include any constraints affecting transport, access or the proposed air supply. If you need equipment for several cable sizes, state each size rather than asking for an undefined universal solution. This helps establish whether different guides, seals or other components are required and which combinations should be confirmed before ordering. Procurement should also address documentation and upkeep. Ask for the operating instructions applicable to the offered model, details of routine maintenance, and information about replaceable components. Clarify how to identify the correct spare parts and which inspection tasks operators are expected to carry out. Consumable availability can be relevant when planning repeated installations, but replacement intervals should come from the manufacturer and actual operating conditions, not assumptions. Where equipment will be used outside Italy, discuss documentation language, destination requirements and any questions concerning the proposed power arrangement. Confirm the commercial terms, delivery arrangements and applicable product documentation directly with Fibernet before committing to a project schedule. Fibernet brings a family-led technical history to these discussions. Its founder, Giancarlo Trinei, worked with early optical cable installations in Italy during the 1980s, and the company was established in 2001. A generational transition began in 2010 with Matteo, Marta and Ismael joining the business. The launch of Lady in 2021 marked the company's entry into cable blowing machines. For buyers, this background is a reason to begin a technical conversation, while the final purchasing decision should still rest on verified specifications and suitability for the particular application. A cable blowing machine for fiber optic cable installation must be assessed against the work it is expected to perform, not simply against a broad product label. Ask how the proposed configuration accommodates your cable, what preparation is required and which operating limits apply. If your specification instead uses the expression drill powered optical fibre cable blowing machine, provide the same measurable requirements so that terminology does not obscure the practical questions. Consistent technical information makes communication easier between project managers, buyers and installation crews across different countries. Explore Fibernet's website and submit your requirements to discuss available equipment. Request a clearly defined proposal covering the machine, relevant accessories and any outstanding compatibility checks. This approach gives your team a firmer basis for comparing options, preparing the site and planning the next cable blowing operation.

Still looking for information about drill powered cable blowing machine?

Fill in the form and discover what Fibernet Srl can do for you!

Contact us!

Before you get started

Have a question?
Start here.

If you prefer, speak to us directly.

+39 346 652 9915
Which cable blowing machine is right for my site?

Compare the cable diameter, duct diameter and installation distance. Lady is compact and lightweight for short runs. Opera is pneumatic and designed for long runs. Geniale is electric and handles both. A Fibernet technician can help you choose.

Can I see the machine in action before I buy it?

Yes. You can request a free hands-on demonstration on your site or at Fibernet’s test facility. Tell us what you need in the form and a technician will arrange it with you. Request a demonstration.

How much does a Fibernet cable blowing machine cost?

To get a price, contact a Fibernet adviser using the form or call +39 346 652 9915.

What support will I get after purchase?

Fibernet offers direct technical support, spare parts ready to ship and dedicated training. If your machine breaks down, a replacement may be available. Ask your technician about availability and terms.

Your next project
starts with the right choice.

Tell us about your job. We’ll help you find the right cable blowing machine.

CallRequest information