Emanuele Zanda
Google reviewRead on Google“An excellent experience on the installer training course. The whole team was professional and knowledgeable.”
Cable blowing machines · Made in Italy
From last-mile connections to long-distance runs, a Fibernet technician can help you choose the right machine for your fibre optic cable installation.
Opera, image 1 of 3
Expert advice direct from the manufacturer / Free demonstration on request
Some of our customers.






Keep your installation moving with Fibernet cable blowing machines.
Photos and stories from installers, published by Fibernet.






Read on Google“An excellent experience on the installer training course. The whole team was professional and knowledgeable.”
Read on Google“I had the chance to try the Opera cable blowing machine on site…”
Read on Google“I really enjoyed this course. It took place in a pleasant setting with friendly, helpful people.”
Stories from installers
Hear the results from the installers themselves. Watch their testimonials right here.
Product videos
Three machines. Find your fit.
Start with the job at hand. Our technician can answer your questions about the right setup.

Compact and lightweight
A compact, lightweight machine for short runs.

Pneumatic power
A pneumatic machine for long cable runs.

Electric, with two gears
For short and long runs. Two gears let you match force and speed to the job.
Specifications for the Fibernet range. The speeds shown are maximum values. Actual results depend on installation conditions and machine setup.
Direct from the manufacturer
When you’re working on site, you need practical answers. With Fibernet, you speak directly to the people who design and build your cable blowing machine.
Speak to a technicianA specialist technician can help when you need it.
Spare parts ready to ship, direct from the manufacturer.
If your machine breaks down, a replacement may be available within 48 hours.
Check availability and terms with your technician.Get help making the most of your machine, from your very first job.
See it in action before you choose
Request a free hands-on demonstration on your site or at Fibernet’s test facility. Discuss a real job with the technician.
Request a free demonstration
Fibre optic cable blower hire starts with a practical question: which machine configuration suits the cable, duct and working conditions on your project? For contractors working in Italy, choosing equipment simply because it is available can create avoidable problems when installation begins. Cable diameter, duct internal diameter, route geometry and the condition of the installed duct all influence the suitability of a blowing arrangement. Fibernet provides a direct point of contact for discussing cable blowing equipment with an Italian company whose first cable blowing machine, Lady, was launched in 2021. If you are considering temporary access to equipment, ask the team to confirm whether a hire arrangement is available for your location, dates and application before making commitments around your site programme. A useful enquiry includes the actual cable specification rather than only its nominal diameter. The cable manufacturer’s maximum permissible pushing force, minimum bend radius and relevant installation limits help define the operating boundaries. Duct details matter equally: internal diameter, material, connectors, changes in direction and any previous use should be identified wherever possible. These details help establish what needs checking before a machine is selected. The suitability of a cable blower for fibre optic cable also depends on the equipment surrounding it. Where compressed air is required, compressor pressure and delivered airflow must match the requirements of the proposed machine and installation arrangement. Pressure alone does not establish suitability, and the maximum rating of a compressor must never be treated as an instruction to operate at that pressure. Hoses, couplings, seals and duct connections must also be appropriate for the intended conditions. Planning these elements together makes an equipment enquiry more useful than asking for a machine without application details. When comparing fibre optic cable blower rental proposals, establish exactly what each offer includes. Ask about cable guides, duct adapters, sealing components, transport arrangements, operating documentation and the responsibilities associated with cleaning or damage. Availability, commercial conditions and any support provisions should be confirmed in writing rather than assumed. Fibernet’s background offers relevant context for this discussion: the company was founded in 2001, building on Giancarlo Trinei’s technical experience dating back to the early installations in Italy during the 1980s. That history does not replace a project assessment, but it explains the practical engineering perspective behind the business. Share your working requirements through www.fibernetsrl.com to begin a focused conversation about suitable cable blowing equipment and the supply options that can actually be confirmed. This approach helps your purchasing team and site supervisor work from the same information, reducing the risk of arranging equipment that reaches the site without the components or operating compatibility needed for the planned task.
A machine arriving on time is only one part of a successful blowing operation. Before arranging equipment, the installation team should establish whether the duct route is ready, whether access points are usable and whether the cable can be fed into the machine without unnecessary resistance. A drum positioned awkwardly, an unsuitable guide path or an unexpected restriction can undermine an otherwise appropriate equipment choice. For this reason, an enquiry about fibre optic cable blower hire is most useful when it includes a realistic description of site readiness, not just the intended installation date. Start with the duct route. Check continuity, connection integrity and cleanliness using methods appropriate to the duct system and the relevant operating procedures. Where testing is required, use suitable equipment and observe the pressure limits of every component involved. Any water, debris or damaged connection should be addressed before blowing starts. Route information should also identify tight bends, significant level changes and intermediate access locations, because these can influence the installation plan and the practicality of completing a section in one operation. A compressed air fibre optic cable blower requires particular attention to the air supply. Confirm the machine’s specified requirements, the compressor’s delivered performance under working conditions and any requirements for air treatment. Moisture control, suitable hoses and compatible couplings are operational considerations rather than optional details. The complete arrangement must be assessed against the manufacturer’s instructions; no generic pressure or distance figure can safely replace those instructions. The team should also confirm how the equipment controls pushing force and how the operator monitors progress during installation. Before using a fibre optic cable installation blower, operators need access to the correct documentation and a clear understanding of stopping procedures. Cable feed should remain controlled, and the work area should allow communication between everyone handling the drum, machine and receiving end. If progress changes unexpectedly, the appropriate response is to stop and investigate rather than simply increase force or air pressure. The cable’s specified limits remain relevant throughout the operation, including during adjustments and restarts. Commercial planning should reflect these practical requirements. Ask what happens if site access is delayed, the route fails its readiness checks or the required accessories differ from those originally requested. Establish collection or delivery responsibilities and any return conditions before agreeing to an arrangement. Fibernet can be contacted with your equipment requirements, while hire availability and contractual terms must be verified directly. Providing clear technical information allows the discussion to focus on the right questions: machine compatibility, required components and the conditions necessary for controlled cable feeding. It also helps distinguish equipment requirements from site issues, giving your team a more reliable basis for scheduling the work and assessing the options presented.
An occasional installation and a continuous programme of cable blowing work create different equipment needs. A contractor facing a single confirmed job may prioritise access for a defined period, while a business with several active teams may place greater value on having its own machine available. Neither approach is automatically more economical. The right comparison considers expected utilisation, transport, accessories, maintenance responsibilities and the cost of disruption if equipment is unavailable when the site is ready. Fibre optic cable blower hire should therefore be evaluated as an operational decision, not simply as a daily rate. Begin with the actual schedule. Identify when the machine must arrive, how long preparation and checks will take, and whether the planned work depends on third parties completing their tasks first. A short installation window may still require additional time for delivery, inspection and return. Conversely, buying equipment for an uncertain workload can tie up funds without providing enough productive use. Make the comparison using realistic scenarios rather than assuming that every planned working day will become a completed installation day. A meaningful fibre optic cable blower price comparison also needs a consistent equipment scope. Two offers may cover different cable ranges, duct interfaces, drive arrangements or accessory packages. One may include components that another treats separately. Ask for a clear description of the proposed configuration and compare the same application requirements across each option. Avoid relying on an advertised maximum installation distance as a standalone measure of value: achievable results depend on the cable, duct route, preparation and operating conditions. If you are assessing a used fibre optic cable blower alongside a new machine or temporary access arrangement, check condition and documentation carefully. Relevant questions include the maintenance history, wear on the feeding components, the availability of compatible seals and guides, and whether the operating instructions correspond to the actual machine. Any inspection should follow the manufacturer’s procedures and be carried out by a suitably competent person. A lower purchase cost is not necessarily an advantage if essential components are missing or the equipment cannot be matched to the intended work. Fibernet’s development reflects a long-term commitment to cable blowing equipment. Founded by Giancarlo Trinei in 2001, the company began its generational transition in 2010 with Matteo, Marta and Ismael joining the business, and introduced Lady in 2021. For buyers evaluating Italian equipment, this background provides context without replacing the need for precise specifications and written commercial terms. Contact www.fibernetsrl.com with your cable and duct details, anticipated workload and project location. Ask the team to clarify available equipment, applicable supply arrangements and any destination-specific requirements. That information gives your business a sounder basis for deciding between temporary access and ownership, without assuming that hire, delivery schedules or particular support services are available before they have been confirmed.
Fill in the form and discover what Fibernet Srl can do for you!
Contact us!Before you get started
If you prefer, speak to us directly.
+39 346 652 9915Compare the cable diameter, duct diameter and installation distance. Lady is compact and lightweight for short runs. Opera is pneumatic and designed for long runs. Geniale is electric and handles both. A Fibernet technician can help you choose.
Yes. You can request a free hands-on demonstration on your site or at Fibernet’s test facility. Tell us what you need in the form and a technician will arrange it with you. Request a demonstration.
To get a price, contact a Fibernet adviser using the form or call +39 346 652 9915.
Fibernet offers direct technical support, spare parts ready to ship and dedicated training. If your machine breaks down, a replacement may be available. Ask your technician about availability and terms.
Tell us about your job. We’ll help you find the right cable blowing machine.